Search Site
Support News
JN-SW-4030 SDK Libraries Updated Update to correct analogue peripherals issue introduced in v1.3 Friday, 5th December 2008
JN-SW-4030 SDK Libraries Updated Maintainance Release (JenNet 1v4) Friday, 5th December 2008
JN-RM-2035 Jenie API Reference Manual Updated Updated for Jenie 1.4 Friday, 5th December 2008
JN-RM-2036 AT-Jenie Quick Command Reference Updated Updated for Jenie 1.4 Friday, 5th December 2008
JN-RM-2038 AT-Jenie Reference Manual Updated Updated for Jenie 1.4 Friday, 5th December 2008
JN-UG-3041 JenNet Stack User Guide Updated Updated for Jenie 1.4 Friday, 5th December 2008
JN-UG-3042 Jenie API Updated Updated for Jenie 1.4 Friday, 5th December 2008
JN-UG-3028 Code::Blocks IDE Updated Updated for Jenie 1.4 Friday, 5th December 2008
JN-UG-3043 AT-Jenie User Guide Updated Updated for Jenie 1.4
| Solutions (1 to 10 of 21) | Show 10 | 100 | All | Next |
|---|
| Solution | Viewed | |
|
How do I identify a Jennic chip on the network? What is Jennic's IEEE address? Jennic has the IEEE Organisationally Unique Identifier (UID) 0x00158D, which will be the top 24-bits of the ... solution00003 2008-05-01 Hardware » Function » programming |
536 | View Solution |
|
How do I read the JN51xx MAC address? The MAC address location can be found by calling pvAppApiGetMacAddrLocation() The prototype can be found in ... solution00007 2008-05-01 Hardware » Function » programming |
482 | View Solution |
|
How are the LQI and MSQ values for received data packets calculated? The LQI value generated whenever a data frame is received is based upon the signal strength. The JN5121 ... solution00004 2008-05-01 Hardware » Function » RF Power |
624 | View Solution |
|
How do I set the output power of the radio? The Tx power can be dynamiclly changed by calling eAppApiPlmeSet(PHY_PIB_ATTR_TX_POWER,level) For example: bool_ ... solution00008 2008-05-01 Hardware » Function » RF Power |
666 | View Solution |
|
How do I read from (and write to) the UART ? The Jennic SDK contains a number of routines for writing data to the UART, (notably vPutC and vPrintf in C:\Jennic\cygwin\jennic\SDK\Chip\Common\Source\Printf. ... solution00018 2008-10-08 Hardware » Interface » programming |
320 | View Solution |
|
Are there any USB dongles available that use JN51xx devices? Although Jennic do not produce USB dongles they are available from several third parties: MSP Technology ... solution00009 2008-04-02 Hardware » Interface » USB |
580 | View Solution |
|
What are the minimum connections required for programming modules? 1) Connect power and ground on pins 24 (VDD), 25 (GND) & 26 (VSSA). 2) Ensure that pins 9 (SSZ) and 13 ... solution00001 2008-03-03 Hardware » JN5139 » programming |
749 | View Solution |
|
If your hardware contains a Jennic module then it will have been programmed with a MAC address during manufacture. ... solution00016 2008-05-19 Hardware » Modules » programming |
530 | View Solution |
|
Are the 333kHz spurs seen when measuring the transmit power in continuous wave mode normal? Transmit output power can be measured using the JN-AN-1021 Module Lab Test Utility. The 'Transmit Power Test ... solution00013 2008-05-01 Hardware » Modules » RF Power |
379 | View Solution |
|
My application requires longer distances between nodes, how can you support this? The Jennic 'JN5139-xxx-M02/04' High Power Modules are high RF power, improved sensitivity modules for extended ... solution00010 2008-04-07 Hardware » Modules » RF Power |
573 | View Solution |